Price: $30.99 - $22.39
(as of Apr 13, 2024 06:27:32 UTC – Details)
Product Description
STUD FINDER WALL SCANNER
Whether you are hanging pictures, putting up a new set of shelves or getting ready to start an addition, knowing where the studs are in a wall can be extremely handy! And A good stud finder can be the difference between a successful DIY home project and disaster. That is why a stud finder is important.
JAXWQ stud finder uses UPGRADED SMART SENSORS which can sense the change in density in the space behind the wall and locates the stud center with GREAT ACCURACY. You will not worry to drill many error holes on the wall while putting up a TV bracket, shelf unit, or even just a set of coat hooks on drywall.
How to use AC mode
Note: If in AC scan mode/Metal scan mode, you need to put the tool in the air to calibrate it.
Step 1: Put the tool in the air and press the ON/OFF button to turn on, then choose AC mode or Metal mode.
Step 2: Press Calibrate Button to start calibration, the decreasing bars will disappear the buzzer will beep one time and the calibration is completed. Then releases the scan button.
Step 3: Place the whole device against the wall, slowly slide the tool across the surface. Mark the location where you get the highest AC indication (the most Middle bars on the screen). (Figure A): If it is a strong target, the top indicated arrow will show, and a steady beep will sound. Continue in the same direction until display bars reduce. Reverse direction and mark the spot where the display bars peak from the reversed direction. The midpoint of the two marks is the location of the center of the live AC wiring. If the unit indicates live electricity over a large area, you can reduce the sensitivity of the tool to refine the scanning area and more accurately locate the live AC wiring by following steps 4 and 5 below.
Step 4: (Figure B) To further pinpoint the location of the live AC wiring, scan the area again. Release the Scan button and then turn the unit back on, this time starting on the wall over one of the previous marks. This will reset the tool to lower sensitivity and narrow the scan area.
Step 5: (Figure C) Scan in both directions as in Step 3. The area indicated should become smaller so you can more precisely identify the location of live AC wires.
For the Frames of Figure A B C, please kindly check the instruction in the package.
Stud Scan Detection
This stud locator has 3 stud scan modes. Deep Scan Mode scans through 2 layers of drywall up to 1.5 in. (38 mm) deep. DeepScan Mode is a higher sensitivity scanning mode that should be used when there are extra layers of wallboard or paneling. To minimize false positives and/or finding other objects further behind the wall that may not be a stud, always start your scan in the 0.5in. or 1 in. StudScan Mode first.
After you detect the center of an object, Please Use Metal Scan to determine if the reading in Stud scan mode was a wood stud, metal stud, or pipe.
Metal Scan Detection
JAXWQ wall detector can locate metal studs in StudScan mode, DeepScan mode, and Metal Scan Modes. Since JAXWQ stud finders are looking for a change in density behind drywall, not a particular material, in StudScan and DeepScan Modes the detector will react to metal studs the same as it would for wooden studs.
Wire Warning Detection
Wire Warning detection indicates the presence of live, unshielded electrical wiring up to 2 inches (51 mm) deep. For Safety, in all modes, this wall scanner always detects and indicates the Live AC Wire.
Note: WireWarning Detection works in both StudScan / DeepScan / MetalScan Modes. The WireWarning Detection Icon will flash when live, unshielded wires are detected.
How to use Stud mode
Step 1: Calibrate the tool before every scan
Place the whole device against the wall, then press and hold the calibration button( on the side of the tool) to calibrate this tool. Wait for the reducing bars to disappear and beep to confirm calibration has been completed.
Note: In stud/deep mode, put it on the wall where you want to detect to calibrate it; In AC/Metal mode, put it in the air to calibrate it.
Step 2: Scan the wall
After finishing calibration, please release the calibration button. Then move the stud finder along the wall slowly, if you shake or lift the scanner accidentally, the device needs to be re-calibrated.
Step 3: Find the location of the stud
When the signal bar is full and the beep alarm is loudest, it means you have found the center of an object. Mark it with your pencil.
Then choose the Metal Scan mode to test whether it is a metal. After you confirm that it is not a metal, it means that you found the center of a stud. (More details refer to the above description of “Metal Scan Detection”)Then you can drill it to hang the thing.
Accurate and Rapid: The wall stud finder adopts an intelligent micro-sensor chip with the highest sensitivity which can accurately and quickly find edges and center of metal, studs, joists, pipes, and live AC wire behind walls, floors, and ceilings. Fast detection saves users time and effort, making task completion easier. It must be ultimate gifts for professionals, homeowner,s and DIY enthusiasts.
Multiple Scan Modes: Our wood stud finder offers multiple scan modes, including stud scan, deep scan, and metal scan, giving you the ability to detect various materials and depths. Stud scan mode finds the center of the stud, while deep scan mode detects the width of larger objects like pipes and wires. Lastly, metal scan mode detects the presence of metal, useful for finding plumbing behind walls. This holiday season, give the gift of peace of mind with a electric stud finder.
High Visibility and Comprehensive Display: Our stud scanner is equipped with a bright, backlit LCD display that shows the center, edge, and location of detected studs, as well as the battery status. Along with the visual display, our stud finder also provides audio alerts and a beep sound to help guide you to the exact location of the stud. The comprehensive display makes it easy for anyone to use, even in low-light settings. It’s the perfect tool gifts for any DIY enthusiast!
Unique Christmas Gifts: Our stud finder is practical and useful Christmas gifts for men/women who want to hang shelves, mirrors, or other heavy objects on the wall without damaging the surface. Moreover, it is handy for detecting live wires and pipes behind the walls, preventing accidents and costly repairs. Giving a stud finder as a Christmas gift shows that you care about safety, efficiency, and practicality, making it a thoughtful and valuable present.
Wide Use: our wood detector for wall is a versatile, reliable, and user-friendly tool that can make any job more efficient and effective. This stud detector quickly locates wood, metal, and AC wires hidden in the walls, floors, and ceilings of the house. Helping you avoid danger when hanging and installing TV mounts photo frames, wall cabinets, garage racks, shelves, mirrors, bathroom handles and other decorations. Give the gift of convenience and comfort with this practical gadget.